How To Repair Whirlpool Washing Machine Agitator
Washer Agitator Repair Guide
This washer agitator repair guide will walk y'all through repairing 3 types of agitators the: Whirlpool dual activeness agitators, GE agitators (made before 1995) and GE agitators (fabricated afterwards 1995). The Whirlpool anarchist has agitator dogs that will strip out causing the top of the agitator to plow both ways. This causes information technology not to mix the clothes properly resulting in poorly washed clothes. The one-time style GE washer has an agitator spine up inside the agitator that connects the agitator to the transmission shaft. This spine will sometimes strip out. If this happens the agitator will not turn at all. The new fashion GE anarchist has a coupling nether the agitator that will besides strip out. This will likewise cause the anarchist not to turn at all. Below are instructions for repairing all three types.
Whirlpool Washer Agitator Repair If the top of your Whirlpool dual action anarchist will turn both ways the agitator dogs are stripped out.
1. Remove the cap or cloth softener dispenser off the summit of the agitator.
2. Under that cap you should encounter another cap, remove it.
3. Remove the 7/16 bolt down in the agitator that holds the agitator on.
4. Pull the agitator upwardly and out of the washer.
five. Down in the anarchist you should run across two tabs that are bent over, straighten them out. And so divide the tiptop of the agitator from the bottom by simply pulling them apart.
vi. Once apart y'all should see the agitator dogs in a holder, remove them and install the new ones.
When putting the agitator back together you must line upwards the two tabs while holding down on the domestic dog holder and so that they won't fall back out. Once the tabs are lined upwardly you should exist able to push the agitator dorsum together. These parts can exist purchased at AppliancePartsPros.com.
Whirlpool Washer Agitator Dogs Replacement Video
GE Washer Agitator Repair
New way
On the new style GE washers there is an agitator coupling under the agitator that will sometimes strip out. To repair this, remove the agitator by pulling information technology direct upwardly and out.
Tip- if you tin can't get your fingers nether the agitator you can slip a chugalug under the agitator and then pull by that.
Once the anarchist is off you should see a yellow coupling held on past a 7/16 commodities. Remove that bolt and pull the coupling up and off the transmission shaft. Sometimes information technology will be hard to remove and you might take to knock it up with a hammer. Once off you should exist able to slide the new on back on, bolt information technology downwards and push the anarchist back on. Agitator couplings can be purchased at AppliancePartsPros.com.
Old manner
On GE old way washers (fabricated before 1995) the anarchist has a spine within the anarchist that will sometimes strip out. When this happens the anarchist will not move. The hardest part virtually this washer agitator repair is removing the old spine from the agitator. They brand a special tool that will brand this easy simply its not practical for a do-it-yourselfer to buy a tool for a simple one-fourth dimension job. I have one of these tools but for the purpose of this website I went to my local hardware store and purchased a few things to make my own tool for under $ten. While information technology is non nearly as practiced as the real tool it will go the chore done.
Parts needed
One ½ inch threaded rod
One iii/8 by ¼ blackness iron bushing
2 ½ inch hex basics.
One ½ inch washer.
A flake slice of 2X4 well-nigh xviii inches long.
one. Drill a ½ inch hole in the middle of the 2X4 board.
ii. Bolt the 2X4 to one end of the rod. Be sure it is tight or information technology will slip when you try to turn it.
three. Screw the bushing onto the other end of the rod.
4. Insert the rod into the agitator and screw the bushing into the anarchist spine that needs removing from the anarchist. Use the 2X4 every bit a handle printing downwardly on it and twist. Make certain it is tight so that it won't sideslip out when you endeavor to pull out the agitator spine.
v. Unbolt the 2X4 and remove both basics.
6. Slide the 2X4 downwardly the rod to the agitator.
seven. Slide the washer to the 2X4.
8. Tread 1 of the nuts downwardly to the 2X4.
9. Continue to turn the nut until the anarchist spine pulls up and out.
10. Bolt the 2X4 dorsum onto the rod as you did in step 2.
11. Screw the new spine onto the bushing.
12. Lubricate the new rubber office of the new spine with liquid soap then that it will printing into the agitator easily.
13. Press the new spine into the agitator.
Anarchist spines can be purchased at AppliancePartsPros.com. I hope this washer agitator repair guide helps yous in repairing your agitator.
Return From Washer Agitator Repair Guide
Source: http://www.appliance-repair-it.com/washer-agitator-repair.html
0 Response to "How To Repair Whirlpool Washing Machine Agitator"
Post a Comment